PDR 110X Car Paintless Dent Repair Puller Remover Lifter Dint Hail Damage Kit

Description

Product Description
NOTE: THERE IS NO INFLUENCE ON TEH DIFFERENT COLOR OF THE DENT PULLER AND THE GLUE GUN
Package:
1 * Glue gun (blue)
1 * Gold dent lifter(green)
1 * Bridge Dent Puller（silver）
12 * Black glue tabs
2 *  A suit of 10 red glue tabs
2 * A suit of 10 blue glue tabs
1 * Tap down hammer
1 * rubber scraper(yellow)
15 * Hot glue sticks(yellow)
1 * Blue duster cloth
1 * Instruction book(black)
1 * Sprinkling can
1 * Rubber hammer
1 * Tap down pen with 9 metal cusps
1 * Tool kit(Red)
1 * line board (dents seeker)
1 * A suit of 12 BK-type crowbar (27cm,0.5cm)
1 * A suit of 12 BK-type crowbar (52cm,0.8cm)
1 * A suit of 12 BK-type crowbar (39cm,0.7cm)
1 * A suit of 12 BK-type crowbar (34cm,0.5cm)
1 * A suit of 12 BL-type crowbar (46cm,0.6cm)
1 * A suit of 12 BL-type crowbar (29cm,0.8cm)
1 * A suit of 12 BL-type crowbar (36cm,0.8cm)
1 * A suit of 12 BL-type crowbar (39cm,0.8cm)
1 * A suit of 12 BL-type crowbar (47cm,0.8cm)
1 * T-Bar with wave texture
1 * Mini T-Bar(Red)
3 * Suction cup
Why dent lifter?
-Dent lifter is quite easy to operate, no complicated guidance needed.
-Capable of repairing small/mid-sized dent with width-adjustable base.
-Deals with most dents with an affordable cost.
-Can be used repeatedly with extra glue pulling tabs provided in this kit.
Basic Steps of Paintless Dent Repair
1. Mark the dent with with marking pen.
2. lnsert the glue stick into the glue gun and heat the stick for 3-5 minutes.
3. Apply the melted glue on the tab, remember to start from the center of tab and make sure the glue is even and full.
4. Align the tab with the center of the dent and slightly press the tab for 3-5 minutes until it cools down and the tab is fixed on the dent.
5. Choose different tools for different types of dents and follow corresponding step:
-Dent Lifter: Buckle the lifter till it is fastened, hold the handle gradually to pull the dent, repeat several times till the surface of the dent flattens or slightly bulges. Notice: do not pull too fiercely or the tab could fall off.
-Bridge Puller: Put the screw part of the tab through the hole in the middle of the bridge. Install the nut and screw it carefully till the surface of the dent flattens or slightly bulges. Notice: do not pull too fiercely or the tab could fall off.
6. If the result is not so ideal, use hammer and tap-down-pen to improve the result slowly, the tap-down-pen has replaceable tips, for beginners we the flat one will be recommended.
7. Remove the glue tabs and glue with scraper, if they are hard to remove, spray some alcohol first and then try again.
High success rate
Super PDR dent repait kit provides higher success rate compared to others, that's the result of the premium quality and unique design of Super PDR.
Wide application
The PDR kit removes not only dent on cars, but also on refrigerator, washing machine etc. And the glue gun and sitcks can be widely used in handworks, DIY projects and home repair.
Comprehensive kit
Beside the dent pullers, the kit also contains hammers and leveling pen with replaceable tips, to that you could keep improving the repair result until it's perfect.